泰安揚帆數控科技有限公司為您提供山東自動焊接設備等相關信息發布和資訊展示,敬請關注!
咨詢服務熱線:
0538-5358300

新聞資訊

推薦產品

行業新聞

固定點焊機故障維修技巧

來源:http://www.lfgwow.com/  發布時間:2021-12-17 瀏覽次數:

開機LCD無顯現:

No display on LCD after startup:
在沒停電的狀況沒有顯現,可能是電源線有問題,查看電源線路反是不是有短路了,假如是保險管燒毀,只需改換異常規格的保險管就行了。
In the case of no power failure, there may be a problem with the power line. Check whether there is a short circuit in the power line. If the fuse is burned, just change the fuse with abnormal specification.
開機有LCD顯現,但是焊接無反響:
LCD displays when starting up, but there is no response during welding:
查看中頻點焊機的充電保險管能否燒毀了,肯定后改換異常規格的保險管應該就能夠處置。
Check whether the charging fuse tube of the medium frequency spot welding machine is burned. After confirmation, replace the fuse tube with abnormal specification, which should be able to be disposed of.
有電源指示,無焊接火花:
With power indication and no welding spark:
很多緣由都會招致這種狀況的發作,比方說:焊接參數調理不正確、電極磨損過渡、電極下端面與電池距離過、;焊接開關損壞、光電開關損壞等等。
Many reasons will lead to the occurrence of this situation, such as incorrect adjustment of welding parameters, electrode wear transition, excessive distance between the lower end face of the electrode and the battery; The welding switch is damaged, the photoelectric switch is damaged, etc.
焊點不牢的現象:
Loose solder joints:
檢查電極頭外形、截面能否適宜。?普通焊板的時分會呈現中頻點焊機越來越難用的狀況,第一就是思索可能是電極太熱,電阻過大。
山東自動焊接設備
Check whether the shape and section of the electrode head are suitable.? The time of ordinary welding board will present the situation that the medium frequency spot welder is becoming more and more difficult to use. The first is to think that the electrode may be too hot and the resistance is too large.
焊點壓痕嚴重并有擠出物:
Severe indentation and extrudate on the solder joint:
指的是焊接完成以后外表燒傷嚴重,有弧坑,檢查電流能否過大或壓力能否太小,電流過大會影響焊接工件的外表焊接效果,壓力太小會呈現擠出物。
It refers to that after welding, the surface is severely burned and there are arc pits. Check whether the current is too large or the pressure is too small. Excessive current will affect the surface welding effect of the welded workpiece, and extrusion will appear if the pressure is too small.
焊接時容易打火,以至燒焦電池外殼:
It is easy to ignite during welding, and even scorch the battery shell:
中頻點焊機電極壓力偏小、電極下端面粘有異物、焊接電流過大、兩電極高度不在同一水平面。
The electrode pressure of the medium frequency spot welder is too small, foreign matters are stuck on the lower end face of the electrode, the welding current is too large, and the height of the two electrodes is not in the same horizontal plane.

上一篇:山東數控焊接設備各方面內容
下一篇:最后一頁

老司机午夜精品视频资源-女人另类牲交ZOZOZO-日本被黑人强伦姧人妻完整版-窝窝人体色WWW